二氧化碳儲罐材料
絕熱性能
絕熱材料選用熱態下的珠光砂充填?yuàn)A層并抽真空，夾層封結后真空度標準為：
有效容積：小于等于 10m 3 真空度≤ 2Pa ，大于 10m 3 小于等于 50m 3真空度≤ 3Pa ，大于 50m 3 小于等于 100m 3 真空度≤ 5Pa ，以精湛的技術，獨特的填充工藝，質量保證承諾，以達到的絕熱效果。
安全技術特性
低溫液體二氧化碳儲罐采用 “組合、安全系統閥”使用兩組安全閥同時工作，在安全閥定期校驗時可關閉一側，另一側繼續工作，確保儲罐的安全運行。
操作系統
儲罐內容器上部設置了壓力表，差壓式液位計和液位對照表，可以隨時掌握內容器儲存量及壓力變化，便于充裝及排液時的操作。
檢測系統
儲罐下部設置了儲罐真空檢測、真空規管及真空閥可定期或隨時用真空計進行檢測夾層真空度，確保儲罐的安全運行。

維護與檢修 Maintenance and repair
【產品詳情圖片】
1.儲罐的使用與維護，應按“壓力容器安全技術監察規程”要求和本說明進行。
The use and maintenance of the storage tank shall be carried out according to the requirements of the Pressure Vessel Safety Technical Supervision Regulations and these instructions
2.日常檢查與維護 Daily inspection and maintenance
儲罐在運行過程中，要經常檢查安全閥、壓力表、液位計工作是否正常，閥門管路是否有泄漏，外部有無異常現象，發現問題及時處理。
During operation of the tank, check the safety valve, pressure gauge and liquid level meter regularly, whether the valve line is leaking, whether there is any abnormal phenomenon outside, and find the problem to be handled in time.
3.定期校驗 Regular verification
3.1安全閥整定壓力不大于2.27Mpa，每年至少校驗一次，并加鉛封，作好記錄。
Safety valve setting pressure is not more than 2.27Mpa, at least once a year, and add seals, make a record.
3.2定期檢查夾層真空度，未裝低溫介質的情況下真空度應低于65Pa，裝有低溫介質的情況下，真空度應低于10Pa為合格。
Regularly check the sandwich vacuum, the vacuum should be less then 65Pa without vacuum medium; with a low temperature medium, the vacuum should be less than 10Pa for the pass.
【產品詳情圖片】
【標題】

【標題】
【變量2】【變量1】
【產品詳情圖片】
山東中杰特種裝備股份有限公司是國內知名的低溫儲罐生產廠家，具有A1，A2壓力容器設計、制造許可證，專業從事液氧LO2、液氮LN2、液氬LAr、液態LCO2及液化天燃?xì)猓↙NG）等低溫液體貯罐、大型常壓貯罐和Ⅰ、Ⅱ、Ⅲ類非標壓力容器設備、化工設備，產品廣泛用于制藥、石油化工、有機合成、冶金、食品、醫療、生物工程、國防等行業。三十幾年來，企業規模不斷發展壯大，現擁有固定資產3.5億元，生產廠區3個，具有先進的加工設備和完善的檢測設備，公司現有職工800余人，年銷售4億多元，并把低溫壓力儲罐作為公司爆品打造。
【產品詳情圖片】

充液的操作 filling operation
【標題】
充液分為充液和補充充液。
充液的操作如下：
Filling fluid is divided into the first filling and filling fluid.
The first filling operation is as follows:
2.1.1 儲罐吹除置換干凈達到要求后，將充液管線與儲罐的充液接頭連接，液位計組合閥處于平衡狀態準備充液。
After the tank blows off to replace the cleanliness meets the requirements, the filling liquid line is connected with the liquid filling joint of the tank, and the liquid level gauge combination valve is in an equilibrium state to be filled.
2.1.2充入與液體二氧化碳純度相同的氣體，使罐內壓力達到0.8 Mpa以上，方可進行充液。 filled with the same purity of liquid carbon dioxide gas, the tank pressure reached 0.8 Mpa above, before filling.
2.1.3 將充液管線接通槽車，先開啟V5殘液閥，排出管線內的雜質氣體后，再開啟V1進液閥和V7排氣閥，V8液位計組合閥處于全開狀態，顯示液位計讀數進行充液。
The filling liquid line connected tanker, first open the V5 raffinate valve, exhaust gas impurities within the pipeline, and then open the V1 inlet valve and V7 exhaust valve, V8 level gauge combination valve is fully open state, Display level meter readings are filled.
2.1.4 在充液過程中，當液位計指示液位接近標定值時，可間斷開啟V4充滿指示閥，如有液體噴出，應立即停止充液，關閉V4充滿指示閥。
During the filling process, when the liquid level gauge indicates the liquid level approaches the calibration value, the V4 may be intermittently opened to indicate the valve. If any liquid is ejected, liquid filling should be stopped immediately and the V4 valve should be closed.
2.1.5關閉V1進液閥和V7排氣閥，打開V5殘液閥，拆下充液管線，充液結束。
補充充液的操作與充液的操作方法相似，不同點是補充充液時一開始就可以大量充液。
Close the V1 inlet valve and the V7 exhaust valve, open the V5 residual valve, remove the filling line, and fill with liquid.
The procedure for replenishing the priming solution is the same as for the first priming procedure, except that the priming solution can be replenished extensively from the beginning.
【產品詳情圖片】
【標題】

http://www.7qe.net