1、高純二氧化碳主要用于電子工業，二氧化碳激光器、檢測儀器的校正氣及配制其它特種混臺氣，在聚乙烯聚合反應中則用作調節劑。
2、固態二氧化碳廣泛用于冷藏奶制品、肉類、冷凍食品和其它轉運中易的食品，在許多工業加工中作為冷凍劑，例如粉碎熱敏材料、橡膠磨光、金屬冷處理、機械零件的收縮裝配、真空冷阱等。
3、氣態二氧化碳用于碳化軟飲料、水處理工藝的pH控制、化學加工、食品保存、化學和食品加工過程的惰性保護、焊接氣體、植物生長劑，在鑄造中用于硬化模和芯子及用于氣動器件。
還應用于殺菌氣的稀釋劑（即用氧化乙烯和二氧化碳的混臺氣作為殺菌、殺蟲劑、熏蒸劑，廣泛應用于醫療器具、包裝材料、衣類、毛皮、工廠、文物、書籍的熏蒸）。
4、液體二氧化碳用作致冷劑，飛機、和電子部件的低溫試驗，提高油井采收率，橡膠磨光以及控制化學反應，也可用作滅火劑。
5、超臨界狀態的二氧化碳可以用作溶解非極性、非離子型和低分子量化合物的溶劑，所以在均相反應中有廣泛應用

結構說明 Structure Description
1. 泄放裝置 Discharge device
2. 內膽 Liner
3.保溫層(珠光砂) Insulation (pear sand)
4.外殼 Shell
5.儀表(差壓計、氧壓表、組合閥) Meter (differential pressure gauge, oxygen pressure gauge, combination valve)
6.抽空口及真空閥門Evacuation port and vacuum valve
7.管路閥門 Pipeline Valve
說 明Description:
⑴本儲罐的操作系統多集中于儲罐底部，儀表系統及組合閥設置在筒壁，便于觀察操作.
The operating system of the tank and more concentrated in the bottom of the tank, instrument system and valve combination set in the cylinder wall, easy to observe the operation.
(2) 內膽設置有兩個安全閥S1、S2，夾層泄壓裝置B。
There are two safety valves S1, S2 inside the liner, sandwich pressure relief device B.
(3) 連接形式：進液口→2＂螺紋連接，排液閥→2＂螺紋連接，抽空口→法蘭.
Connection: inlet → 2 "thread connection, drain valve → 2" thread connection, exhaust port → flange.
【產品詳情圖片】
【變量3】【變量2】【變量1】

充液的操作 filling operation
【標題】
充液分為充液和補充充液。
充液的操作如下：
Filling fluid is divided into the first filling and filling fluid.
The first filling operation is as follows:
2.1.1 儲罐吹除置換干凈達到要求后，將充液管線與儲罐的充液接頭連接，液位計組合閥處于平衡狀態準備充液。
After the tank blows off to replace the cleanliness meets the requirements, the filling liquid line is connected with the liquid filling joint of the tank, and the liquid level gauge combination valve is in an equilibrium state to be filled.
2.1.2充入與液體二氧化碳純度相同的氣體，使罐內壓力達到0.8 Mpa以上，方可進行充液。 filled with the same purity of liquid carbon dioxide gas, the tank pressure reached 0.8 Mpa above, before filling.
2.1.3 將充液管線接通槽車，先開啟V5殘液閥，排出管線內的雜質氣體后，再開啟V1進液閥和V7排氣閥，V8液位計組合閥處于全開狀態，顯示液位計讀數進行充液。
The filling liquid line connected tanker, first open the V5 raffinate valve, exhaust gas impurities within the pipeline, and then open the V1 inlet valve and V7 exhaust valve, V8 level gauge combination valve is fully open state, Display level meter readings are filled.
2.1.4 在充液過程中，當液位計指示液位接近標定值時，可間斷開啟V4充滿指示閥，如有液體噴出，應立即停止充液，關閉V4充滿指示閥。
During the filling process, when the liquid level gauge indicates the liquid level approaches the calibration value, the V4 may be intermittently opened to indicate the valve. If any liquid is ejected, liquid filling should be stopped immediately and the V4 valve should be closed.
2.1.5關閉V1進液閥和V7排氣閥，打開V5殘液閥，拆下充液管線，充液結束。
補充充液的操作與充液的操作方法相似，不同點是補充充液時一開始就可以大量充液。
Close the V1 inlet valve and the V7 exhaust valve, open the V5 residual valve, remove the filling line, and fill with liquid.
The procedure for replenishing the priming solution is the same as for the first priming procedure, except that the priming solution can be replenished extensively from the beginning.
【產品詳情圖片】
【標題】

常見故障的處理 Common fault handling
【產品詳情圖片】
1.內罐壓力異常長高 Inner tank pressure abnormally high
1.1可能是V3回氣閥開度過大或閥門失靈，應減小閥門開度或檢修閥門。
May be V3 return valve opening is too large or valve failure, should reduce the valve opening or valve repair.
1.2可能是S1、S2安全閥失靈，到啟動壓力不啟動，應檢查安全閥。
may be S1, S2 safety valve failure, to start the pressure does not start, check the safety valve.
1.3可能是壓力表指示不準確，應校驗壓力表。
may be pressure gauge indicates inaccurate, should verify the pressure gauge.
2.液位計指示不真實 Level gauge instructions are not true
2.1可能是液位計失靈，應檢修液位計。
may be the level gauge failure, should be maintenance level gauge
2.2可能是液位計接頭處泄漏，應檢修接頭連接處，排除泄漏。
It may be a leak at the head of the liquid level gauge. It should repair the connection of the joint and eliminate the leakage
3.蒸發率高，外殼體凝水結霜 High evaporation rate, the outer shell condensate frost
3.1可能是珠光砂未填實或下沉，應補充珠光砂，重新抽真空。
may be unfilled or sinking of pearl sand, pearl sand should be added and re-evacuated.
3.2可能是真空度惡化，應進行真空檢漏，重新抽真空。
may be a deterioration of the vacuum, vacuum leak detection should be carried out, re-vacuum.
4.管道閥門液體流動不暢或堵塞 pipeline valve fluid flow or blocked
可能是液體二氧化碳形成干冰的原因造成，應停止使用，用熱空氣加溫管閥至?xí)惩橹?。May be caused by the formation of dry ice, should stop using, with hot air heating pipe valve until smooth.
【產品詳情圖片】
【標題】

http://www.7qe.net